USBASP USBISP AVR Programmer USB Adapter + 6-to 10 Pin IDC ISP Connector + Cable with ATmega32 Development Board

Description

This USBASP / USBISP AVR Programmer is a versatile, affordable solution for programming AVR microcontrollers such as ATMEGA8, ATMEGA128, and many more. Ideal for Arduino boards, 3D printer controller boards, and other AVR-based projects.

Includes a 10 Pin to 6 Pin Adapter, making it easy to program boards with both 10-pin and 6-pin ISP headers.

 USBASP / USBISP Programmer — Supports a wide range of AVR chips
 10 Pin to 6 Pin Adapter — Compatible with older and newer boards
 Supported chips: ATMEGA8, ATMEGA128, ATMEGA328P, ATTINY series, and many more
 Perfect for:
• Arduino bootloader flashing
• 3D printer mainboard bootloader updates
• DIY electronics projects
• AVR firmware development

Why choose this USBASP programmer?
 Easy to use — plug into USB, connect to ISP header
 No external power needed — powered via USB
 Supports wide variety of AVR MCUs
 Works with popular software: AVRDUDE, Arduino IDE, Atmel Studio, PlatformIO
 Great for flashing firmware to 3D printer mainboards (Ender 3 / CR-10 / etc.)

• Programmer Type: USBASP / USBISP
• MCU Support: ATMEGA8, ATMEGA128, ATMEGA328P, ATTINY series, many more
• Interface: USB 2.0
• Output: 5V / 3.3V selectable (depending on board revision)
• Included: 10 Pin ISP Cable + 10 Pin to 6 Pin Adapter Board

32 I/O pin all the leads
Classic ATmega16 minimum system, eliminating the hassle of soldering
Crystal: The socket hole welding facilitate the buyer to replace the crystal, 8M crystal
Support chips: ATmega16/ATmega32 and chip which pin-compatible
Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply)
DC-005 Power Block (supporting the transposon is 5.5*2.1mm)
Expand outside 4 channel VCC, GND
Reset: Power-on reset and reset button
Power LED (D1) and the program run indicator (D2)
Standard ISP download interface
Size:88mmx38mm/3.47″x1.49″(inch) (approx)

– This programmer is based on Thomas Fischl’s USBasp design and connects to your computer’s USB port. Not only is it quite compact, but the design is really elegant. The USB interface is achieved by using an atmega processor and the rest is done in firmware.
– With 500mA over-current protection self-recovery fuse, and complete protection of expensive computer motherboard
designed for notebook computers, special two 3.6V regulator, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings.
– The well-configured firmware, the speed of the unique adaptive technology, stability and obtain the best balance between speed! Supports firmware upgrade unlimited.

Note: This minimum system development board without AVR chip, you need purchase for chip in additional!

 1x USBASP / USBISP AVR Programmer
 1x 10 Pin to 6 Pin ISP Adapter Board
 1x ISP Cable
1x ATmega32 Development Board

5 000 CFA

Rupture de stock

0
Programmers
UGS : WEMOS2604 Catégorie :
Description

Description

This USBASP / USBISP AVR Programmer is a versatile, affordable solution for programming AVR microcontrollers such as ATMEGA8, ATMEGA128, and many more. Ideal for Arduino boards, 3D printer controller boards, and other AVR-based projects.

Includes a 10 Pin to 6 Pin Adapter, making it easy to program boards with both 10-pin and 6-pin ISP headers.

 USBASP / USBISP Programmer — Supports a wide range of AVR chips
 10 Pin to 6 Pin Adapter — Compatible with older and newer boards
 Supported chips: ATMEGA8, ATMEGA128, ATMEGA328P, ATTINY series, and many more
 Perfect for:
• Arduino bootloader flashing
• 3D printer mainboard bootloader updates
• DIY electronics projects
• AVR firmware development

Why choose this USBASP programmer?
 Easy to use — plug into USB, connect to ISP header
 No external power needed — powered via USB
 Supports wide variety of AVR MCUs
 Works with popular software: AVRDUDE, Arduino IDE, Atmel Studio, PlatformIO
 Great for flashing firmware to 3D printer mainboards (Ender 3 / CR-10 / etc.)

• Programmer Type: USBASP / USBISP
• MCU Support: ATMEGA8, ATMEGA128, ATMEGA328P, ATTINY series, many more
• Interface: USB 2.0
• Output: 5V / 3.3V selectable (depending on board revision)
• Included: 10 Pin ISP Cable + 10 Pin to 6 Pin Adapter Board

32 I/O pin all the leads
Classic ATmega16 minimum system, eliminating the hassle of soldering
Crystal: The socket hole welding facilitate the buyer to replace the crystal, 8M crystal
Support chips: ATmega16/ATmega32 and chip which pin-compatible
Power supply: power adapter or external expansion pin power supply (not support ISP download interface power supply)
DC-005 Power Block (supporting the transposon is 5.5*2.1mm)
Expand outside 4 channel VCC, GND
Reset: Power-on reset and reset button
Power LED (D1) and the program run indicator (D2)
Standard ISP download interface
Size:88mmx38mm/3.47″x1.49″(inch) (approx)

– This programmer is based on Thomas Fischl’s USBasp design and connects to your computer’s USB port. Not only is it quite compact, but the design is really elegant. The USB interface is achieved by using an atmega processor and the rest is done in firmware.
– With 500mA over-current protection self-recovery fuse, and complete protection of expensive computer motherboard
designed for notebook computers, special two 3.6V regulator, a perfect match to level, get rid of the instability of hardware hidden! Target board power mode jumper settings.
– The well-configured firmware, the speed of the unique adaptive technology, stability and obtain the best balance between speed! Supports firmware upgrade unlimited.

Note: This minimum system development board without AVR chip, you need purchase for chip in additional!

 1x USBASP / USBISP AVR Programmer
 1x 10 Pin to 6 Pin ISP Adapter Board
 1x ISP Cable
1x ATmega32 Development Board

Related products